How to Fix Low Spots in Shower Floor

A shower floor with low spots can be a real annoyance. It makes the floor difficult to clean, but it can also be dangerous if you slip and fall. Fortunately, there are ways to fix this problem.

In this blog post, we’ll explain what causes low spots in shower floors and how to fix low spots in shower floor using a few simple methods. We’ll also provide some tips on preventing this issue from happening again in the future. So read on for all you need to know about fixing low spots in your shower floor.

It’s not always easy to tell when there is a problem with your shower floor until it starts causing issues. You may have a low spot if you start to notice water pooling in certain areas or the floor feels spongy under your feet.

These problems are usually caused by either the shower floor isn’t level or there being a build-up of soap scum and other debris in the area. If you suspect that your shower floor is uneven, the best way to fix this is to use a level. Place the level on the floor and see if it’s level from front to back and side to side. If it’s not, then you’ll need to adjust the leveling feet until it is.

If you have a build-up of soap scum and other debris, then you’ll need to clean this off before you can level the floor. The best way to do this is to use a power washer or a pressure washer. These devices will blast away the debris and leave your shower floor clean and ready to be level.

Shower Floor

Summary: If you have low spots or water spots in your shower floor, there are a few things you can do to try and fix the issue. You can fill the low spots with caulk or caulking, or you can use a tile backer to create a level surface. You can also seal the entire floor of the shower with a coating or sealant.

Why Is My Shower Floor Uneven?

It is not uncommon for shower floors to become uneven over time. This can happen for a variety of reasons, including:

The House Settling:

As the house settles, it can cause low spots to form on the shower floor. The low spots may not be noticeable at first, but they can become more pronounced over time. If you notice a low spot on your shower floor, it’s important to have it repaired as soon as possible. Otherwise, the problem could get worse and cause the rest of the floor to become uneven.

Poor Installation:

If the shower floor is not installed properly, it could lead to unevenness. Poor installation can also cause the tiles to crack or come loose over time. The cracks can also allow water to seep underneath the tiles, which can cause mold and mildew to grow.

Cracks in the Foundation:

If there are cracks in the foundation, they can cause the shower floor to become uneven. Therefore, it is important to have any cracks in the foundation repaired as soon as possible to prevent further damage.

Tools and Materials

  • Level
  • Power washer or pressure washer
  • Soap
  • Sponge
  • Bucket

10 Easy Ways on How to Fix Low Spots in Shower Floor:

1. Use a Level: 

The first step in fixing a shower floor is to use a level. This will help you find the low spots on your shower floor. Level the floor from different angles until you find the lowest point. If the lowest point is in the middle of the floor, then you have a dip. If the lowest point is along the edge of the floor, then you have a hole.

2. Use a Caulking Gun: 

If there are any low spots on your shower floor, you can fill them in with a caulk gun. Make sure to use waterproof caulk so that it can stand up to the moisture in your shower. If you have any big cracks or holes in your shower floor, you might need to use a patching kit to fill them in before caulking.

Fill Them in Before Caulking

3. Use a Grout Saw: 

If you have tile on your shower floor, you can use a grout saw to remove the grout around the affected area. This will give you access to the low spot so that you can fill it in. Just be sure to use a wet saw to avoid damaging the tile. The grout saw will also come in handy if you need to remove any old caulk or grout.

4. Use a Putty Knife:

If there are raised spots on the caulk bead, you can use a putty knife to smooth them down. First, wet the area with a damp cloth. Then, hold the putty knife at a 45-degree angle and run it along the caulk bead. Finally, wipe away any excess caulk with a damp cloth.

5. Use a Power Washer:

If your shower floor is made of concrete, you can use a power washer to remove any dirt or debris that may be causing the low spot. Point the power washer towards the affected area and let it do its job. You may need to repeat this process a few times to get rid of all the dirt.

6. Use a Chisel:

If the low spot is caused by a small piece of tile that has come loose, you can use a chisel to remove it. First, score around the tile with the chisel. Then, tap the chisel with a hammer to loosen the tile. Finally, pry the tile up and away from the shower floor. If you don’t have a chisel, you can also use a screwdriver or another sharp object.

You Can Use a Chisel to Remove It

7. Use a Sander:

If the low spot is in the grout line, you can use a sander to remove it. Start by placing the sander on the floor and turning it on. Then, slowly move it back and forth until the grout is level with the rest of the tile.

8. Use an Epoxy:

If you have a hole in your shower floor, you can use epoxy to fill it in. First, mix the epoxy according to the instructions on the package. Next, use a putty knife to apply the epoxy to the hole. Finally, use a wet rag to smooth out the epoxy.

9. Use a Concrete Patch:

If the low spot is on a concrete shower floor, you can use a concrete patch to fill it in. First, clean out the area and then apply the patch according to the instructions on the package. Next, use a trowel to smooth it out, and then let it dry. Once it’s dry, you can paint or tile over it.

10. Use a Self-Leveling Compound:

If you have a large dip in your shower floor, you can use a self-leveling compound to fix it. This is a quick and easy fix that will take care of the problem for good. First, you will need to clean the area around the dip and make sure that it is free of dirt and debris. Next, mix the self-leveling compound according to the instructions on the package.

Once it is mixed, apply it to the dip in the shower floor and smooth it out with a putty knife. Let the compound dry for 24 hours before using the shower. This will give it time to set properly and create a smooth, level surface.

You Can Check It Out To Fix Pebble Shower Floor

Create a Smooth Level Surface

Frequently Asked Questions

Do I Adjust the Slope in My Bathroom Floor?

it depends on the type of flooring that you have and your specific needs. However, if you’re unsure about how to adjust the slope in your bathroom floor, there are a few ways that you can try.

One option is to install risers above the original floor surface. This will help level out the slope and make walking more comfortable. Alternatively, you could add a layer of insulation underneath the existing tiles or grout to provide some cushioning for feet and knees when entering and exiting the shower or bathtub.

What Do You Put on the Bottom of a Shower Floor?

Most people put shower sand or some type of nonskid material on the bottom of a shower floor in order to prevent water from leaking. This is a common problem because tiles, porcelain, and other hard surfaces get wet and slippery when they’re wet. Not only does this make it difficult to move around in the shower, but it also creates an unsafe environment for those who are using the bathroom.

Should a Shower Floor Be Level?

it depends on a variety of factors, including the type of shower floor you have and your specific needs. That being said, most shower floors are designed to be level so that water doesn’t seep into the floor and cause problems. If you’re not sure if your floor is level, you can try using a level to check.

Why is My Bathroom Floor Sloping?

There are many possible causes for a bathroom floor to slope, and the most common ones include age (the mortar between the bricks starts to crumble), water damage (which can cause tiles to shift and separate from the brickwork), and improper installation or repair of drainage systems.

If you notice that your bathroom floor is sloping noticeably, it’s important to call an experienced contractor in order to assess the situation and recommend a course of action. In some cases, corrected slopes may require the use of retaining walls or other structural supports.

What is the Best Material to Use for Shower Floor?

In order to choose the best material for your shower floor, you need to consider a few things. First, is it necessary? If so, what are the benefits of using this particular type of material? Is it waterproof and easy to clean?

Next, think about the cost. What is the least expensive option that still meets your requirements? And finally, how long will this material last before needing replacement or repairs?

One popular type of shower flooring is ceramic tile. Ceramic tiles are very durable and can withstand heavy use without breaking or deteriorating over time. They are also resistant to stains and require minimal maintenance if kept clean. However, they do not typically conform well to other surfaces such as walls or floors and may require additional installation materials (like grout) if desired.

Another popular choice for shower floors is vinyl plank tile options. These tiles come in many different colors and patterns and usually have a more contemporary look than traditional ceramic tiles.

Vinyl plank tiles tend to be less expensive than porcelain Tile options but may not be as durably built or slip-resistant when wetted down with water). They also tend at times to show wear more quickly, especially if exposed directly to sunlight during warmer months.


Shower floors are often the lowest spot in a bathroom, and as such, they can easily become wet and slippery. This can be dangerous, especially if you have elderly or young family members using the shower. In this post, we’re going to show you how to fix low spots on the shower floor to be safe and comfortable for everyone who uses it.

When repairing a shower floor with low spots, use an epoxy mortar mix to patch the area. The mix can be applied with a trowel or putty knife and should be allowed to dry for 24 hours before using the shower again. If you have any questions about how to fix low spots in shower floor, please don’t hesitate to call us.

Leave a Comment