How to Fix Curtain Rod Holes

If you’ve ever moved and had to take your curtains down, removing the curtain rods is always a pain. The holes they leave in the wall are usually pretty big; if you’re not careful, you can easily damage the paint or wallpaper. This post will show you how to fix curtain rod holes that are barely noticeable. Read on to learn more.

How to Fix Curtain Rod Holes

Summary: Fixing curtain rod holes doesn’t have to be difficult! With the right supplies and some effort, you can easily fix any holes left behind. First, remove the curtain rod, then inspect the area. Clean and apply spackle, let it dry, sand the area and then add primer (optional). Finally, paint the area and re-attach the curtain rod.

Why You Should Repair Curtain Rod Holes

There are a few reasons why you should take the time to repair your curtain rod holes. First, it will make it easier to hang curtains in the future. If the holes are large and damaged, getting the new curtain rods to fit properly can be difficult. Second, repairing the holes will help prevent further damage to the wall. If the holes are left unrepaired, they can become larger and more difficult to fix. Finally, repairing the holes will improve the overall appearance of your home. Large, unsightly holes in the wall can be quite off-putting to guests.

Step by Step on How to Fix Curtain Rod Holes:

1. Gather Your Supplies

The first step is gathering all the supplies you’ll need. You’ll need a putty knife, spackle, sandpaper, and paint. Depending on the wall anchors used to hang the curtain rod, you may also need a screwdriver. Gather all your supplies before you begin so you’re not searching for them in the middle of the project.

2. Remove the Curtain Rod

The next step is removing the curtain rod. This is because you’ll need to access the wall behind it to make the repairs. Carefully remove the curtain rod and set it aside. To remove the rod, first, remove any decorative finials. Next, unscrew the brackets that are holding the rod in place. Once the rod is removed, set it aside in a safe place. If any wall hooks or other hardware are still attached to the rod, remove them as well.

Remove the Curtain Rod

3. Inspect the Area

Once the curtain rod is removed, take a look at the area around the holes. If there are any cracks or other damage, you’ll need to repair those before moving on. Inspect the area and make any necessary repairs before proceeding.

4. Clean the Area

The next step is to clean the area around the holes. This will help the spackle to adhere properly and create a smoother finish. Use a damp cloth to wipe away any dirt or dust around the holes. First, clean any dirt or dust from the surface of the hole. Then, use a vacuum attachment to remove any debris from inside the hole. If necessary, use a toothbrush to remove any stubborn dirt. Allow the area to dry completely before moving on.

5. Apply the Spackle

Once the area is clean, it’s time to apply the spackle. Spackle is a putty-like substance that is used to fill holes and cracks in walls. It dries hard, so it’s perfect for this project. To apply the spackle, first dip the putty knife into the tub. Then, scrape some of the spackle onto the hole. Use the putty knife to spread the spackle evenly over the hole. If necessary, use your finger to smooth out the spackle. Allow the spackle to dry completely before moving on.

6. Let the Spackle Dry

After you’ve applied the spackle, it’s important to let it dry completely. Depending on the temperature and humidity, this can take anywhere from a few hours to a full day. Do not try to sand or paint the spackle until it is completely dry. If you do, you’ll end up creating a mess. Avoid using the area around the repair while the spackle is drying. This will help to prevent any accidental damage.

7. Sand the Area

Once the spackle is dry, it’s time to sand the area. This will help to create a smooth, even surface. To sand, the area, use a piece of fine-grit sandpaper. Rub the sandpaper over the spackle in a circular motion. Sand until the area is smooth. Try to avoid sanding too much, as this can damage the wall. Once you’re finished sanding, use a vacuum attachment to remove any dust.

8. Apply Primer (Optional)

If you’re planning to paint the area, you’ll need to apply primer first. This will help the paint to adhere properly and create a smooth finish. To apply primer, use a roller or brush. Apply the primer evenly over the entire area, making sure to get into all of the nooks and crannies. Once the primer is dry, you’re ready to paint.

Clean the Area Around  The Holes

9. Paint the Area

Now it’s time to paint the area. Choose a paint color that matches the rest of the wall. To apply the paint, use a brush or roller. Start at the top of the wall and work your way down. Apply the paint in even strokes, going with the grain of the wall. Let the paint dry completely before moving on to the next step.

10. Re-Attach the Curtain Rod

Once the paint is dry, you can re-attach the curtain rod. First, screw the brackets back into the wall. Please make sure they are tight, so the curtain rod doesn’t fall. Next, slip the end of the curtain rod into each bracket. Finally, twist the set screws to secure the curtain rod in place. And that’s it! Your curtain rod should now be level, and your curtains should hang evenly. If you have any gaps between your curtain and the wall, you can use drapery hooks to close them. Drapery hooks are small hooks that attach to the wall and hold the fabric in place. Insert the hook into the gap and twist it to secure.

How Much Does It Cost to Fix a Curtain Rod Hole?

Normally, it would cost around $100 to fix a curtain rod hole. However, the cost of fixing a curtain rod hole will depend on the size and depth of the hole and the type of wall you have. If the hole is small and shallow, you can likely fix it yourself with some spackle and paint. However, if the hole is larger or deeper, you may need to hire a professional. Again, the cost of hiring a professional will depend on the size of the hole and the type of wall you have. Expect to pay anywhere from $50 to $200 for the repair.

Tips and Warnings on How to Fix Curtain Rod Holes:


  1. Be sure that the drill bit you are using is the same size as the dowel.
  2. A wooden dowel will work best to fill the hole, but you can also use a plastic one.
  3. If the hole is too large, you may need to use two dowels side by side to fill it.
  4. Use wood glue to secure the dowel in place if you want.
  5. Once the dowel is in place, you can sand it down so that it is flush with the wall.
Choose a Paint Color


  1. Be careful not to drill too deeply and hit electrical wires or plumbing.
  2. If the hole is too large, you may not be able to fill it with a dowel. In this case, you will need to use a different method to repair the hole.
  3. If the dowel is not flush with the wall after you put it in, it will be visible when you hang your curtains. Sand it down so that it is level with the surrounding wall.

How to Prevent Curtain Rod Holes

1. Use a Drill Stop

When you’re drilling your pilot holes, set a depth stop on your drill bit so you don’t accidentally drill through the other side of the wall. A depth stop is a collar that goes around the drill bit and can be set to a specific depth.

2. Use Wall Plugs

If you’re worried about the strength of your Pilot holes or using a very heavy curtain rod, then wall plugs are a good option. Wall plugs are like big nails that you hammer into the wall and then screw your curtain rod.

3. Use a Curtain Rod Bracket

Using a bracket is the way to go if you want an extra-secure curtain rod. Most brackets will come with screws, and wall plugs included. Screw the bracket into the wall at the appropriate height, and then screw your curtain rod into the bracket.

4. Use Adhesive Hooks

If you’re worried about making holes in your walls, you can use adhesive hooks to hang your curtains. Adhesive hooks are strong enough to hold most curtain rods, but they’re not really made for heavy-duty use.

Use a Curtain Rod  Bracket

5. Use Command Strips

Command strips are another option for hanging curtains without making holes. These strips are very strong and can hold a lot of weight, but they’re not reusable. Simply affix the strips to the wall and then hang your curtain rod on them.

Frequently Asked Questions

Can You Use Wood Filler to Fill Holes in Drywall?

Yes, you can use wood filler to fill holes in drywall. This is a relatively low-cost and easy way to fix small repairs or replacements. Wood filler is made of polyurethane resin and particleboard, so it’s very durable and will hold up well over time. Just be sure not to use too much as this could cause damage that might require more extensive repair work down the road.

Is It Better to Use Wood Filler or Caulk?

As both products have their own set of benefits and drawbacks.

Wood filler is a good option if you want a seamless finish that can last for months or even years. On the downside, the wood filler may contain chemicals and dyes that can be toxic if inhaled or absorbed through the skin. Additionally, it can be difficult to remove once it has been applied, so care must be taken when using this product.

Caulk is less expensive than wood filler and also easier to apply because it dries quickly. However, calk does not last as long due to moisture absorption from the surrounding environment.

Do Curtain Rods Need to Be Hang on Studs?

No, curtain rods don’t need to be hung on studs. In fact, this is a common mistake that people make when installing curtains. Curtain rods are typically made from metal or wood and should not touch the wall if at all possible. Instead, they should be installed about 2 inches away from the wall so that there is plenty of wiggle room for the panels to move.


So, there you have it, How to fix curtain rod holes in no time at all! Just follow our simple steps, and your curtains look as good as new. And if you’re ever feeling adventurous, why not try fixing the holes yourself? It’s definitely a project that can be completed in just a few short hours. We hope you found this post helpful – happy curtain-hanging!

Leave a Comment