How to Fix a Rc Car Steering

Like most people, you probably enjoy spending time with your remote control car. Whether racing around the house or driveway or taking it for a spin in the park, there’s just something about these cars that make people happy.

How to Fix a Rc Car Steering

Unfortunately, even the best of us occasionally have problems with our cars. One such issue that can occur is when the steering becomes jammed. This article will show you how to fix a rc car steering that’s become stuck. So, whether you’re a beginner or experienced rc car driver, keep reading for some helpful tips!

Summary: Fixing an RC Car steering issue requires two main steps: first, making sure the steering is properly connected to the car; and second, ensuring that the servo horn is adjusted correctly. To make sure the steering is correctly connected to the car, check for loose wires or broken parts. . Adjust the servo horn by loosening its screws and sliding it closer or further away from the center of the car, depending on whether you want to increase or decrease turning power.

8 Common Problems in Rc Car Steering

1. Car Is Not Going Straight

The car is not going straight because the wheels are not aligned properly. This can be fixed by adjusting the toe-in or toe-out of the wheels. Another possible reason is that the suspension is not set up correctly. This can be adjusted by changing the ride height, camber, and caster.

2. Car Is Not Turning

If your car is not turning, it could be because the servo saver is too tight. The servo saver limits how much the steering servo can turn the wheels. If it is too tight, it will not allow the servo to turn the wheels far enough. To fix this, simply adjust the servo saver until the car can turn properly.

3. Car Is Turning Too Much

If your car is turning too much, the problem might be that the steering linkage is bent or misaligned. In this case, you’ll need to fix the linkage before you can continue driving your car. First, take the car off of the ground and remove the wheel on the side that’s causing the problem. Second, use a screwdriver to straighten out the linkage. Finally, realign the wheel and put the car back on the ground.

4. Not Responding to Steering Input

There are a few possible causes for this issue. One possibility is that the steering servo may be malfunctioning and not responding to the input from the transmitter. This can be caused by several factors, including a dirty or corroded servo connection, a worn-out servo gear, or a faulty servo motor. Another possibility is that the issue could be with the transmitter itself, such as a loose antenna or low batteries. Lastly, it could be something as simple as interference from another electronic device.

If you think the servo is broken, you can test it by disconnecting it from the car and connecting it to a power source (like a battery or an AC adapter). If the servo moves when you turn on the power, then the problem is probably with the car, not the servo.

Rc Car Battery

5. Car Keeps Veering to One side

The problem is usually caused by a bent steering linkage or broken servo saver. To fix it, first check all the steering components to see if anything is bent or broken. If everything looks okay, then adjust the servo saver to be tighter. This will help keep the steering more stable.

6. Car Won’t Turn

This could be caused by several things, such as a bent axle, a wheel that’s not properly attached, or a servo that’s not working properly. First, you’ll need to figure out what’s causing the problem and then fix it.

7. Car Does Not Respond Quickly

If your car does not seem to respond quickly to your input, it may be because the gears are not properly meshed. You can try to fix this by adjusting the gearbox. If that does not work, you may need to replace the gears.

8. Car Goes in the Wrong Direction

If your RC car starts going in the wrong direction, it is most likely due to a problem with the steering. To fix this, you will need to adjust the trim on the transmitter. The trim is usually located on the top or bottom of the transmitter and is used to adjust the steering.

What Things You’ll Need

  1. Rc car
  2. Phillips head screwdriver
  3. Flathead screwdriver
  4. Pliers
  5. Electrical tape
  6. Jumper cables
  7. Soldering iron and solder

Step by Step Guide: How to Fix a Rc Car Steering

Step 1: Disconnect the Battery

Before you start fiddling with the wiring of your RC car, it is important to disconnect the battery. This will prevent you from accidentally shorting out any of the components while working. Locate the battery and remove it from the car to do this. If your car has a removable battery pack, this will be a lot easier.

Rc Car Has a Removable Battery

Step 2: Remove the Screws

Use the Phillips head screwdriver to remove the screws that hold the top of the car together. There will be two or three screws, depending on the model of your car. Once the screws have been removed, you can lift the top of the car off to access the internal components.

Step 3: Remove the Body

The body of your RC car can often be removed simply by unscrewing a few screws. This will give you access to the car’s inner workings and allow you to start fixing the steering. However, be careful not to lose any of the screws, as they can be difficult to replace.

Step 4: Locate the Steering Arm

The steering arm is the component that is responsible for connecting the steering wheel to the rest of the car. It is often located near the front of the car, and it will have a small hole in it where the screwdriver can be inserted.

Step 5: Inspect the Wiring

Once you have access to the car’s internals, look at the wiring to see if there are any loose connections. If you see any frayed or damaged wires, use the soldering iron and solder to repair them. If the damage is too severe, you may need to replace the entire wiring harness.

Step 6: Replace the Steering Arm

If the steering arm is damaged, you will need to replace it. Use the pliers to remove the old steering arm and then install the new one. Be sure to screw it in tightly not to come loose.

Step 7: Reattach the Body

Once you have finished repairing the steering, reattach the car’s body. Make sure that all the screws are tight so that it does not come loose. Finally, reconnect the battery and test your car to see if the steering is working properly.

Other Alternative Methods to Fix an Rc Car Steering

If your car is still having steering problems, there are a few other things that you can try on how to fix a rc car steering. Here we have listed them below:

Rc  Car Steering Problems

1. Adjust the Alignment:

This is probably the most common method to fix RC car steering problems. Adjust the screws on the front or rear of the car until it’s straight. This can be done by loosening the screws that hold the wheels in place and moving them until the car goes straight.

2. Check the Tires:

Another simple fix is to make sure that the tires are inflated properly. If they’re not, then they can cause the car to pull to one side or the other. Pump them up to the recommended pressure and see if that helps.

3. Lubricate the Gears:

You can do this by using a light oil or a lubricant specifically made for RC cars. Apply a few drops of oil or lubricant to the gears and then work the steering back and forth to distribute it. Doing this regularly will help keep the steering working smoothly.

4. Adjust the Differential:

This is a bit more advanced, but it can be done if familiar with how your differential works. The differential allows your car to turn, and if it’s not adjusted properly, your car will steer poorly. To adjust the differential, you’ll need to loosen the screws on either side. Once it’s loose, you can turn the differential itself to adjust how tight or loose it is. Be careful not to turn it too much, or you’ll damage the gears.

You Can Check It Out to Fix Texture Loss Fivem

5. Check the Battery:

If your car isn’t steering properly, the battery might be blamed. Ensure that it’s fully charged and that the connections are clean and secure. If the problem persists, you might need to replace the battery.

6. Adjust the Trim:

The trim is what helps your car drive in a straight line. If it’s not adjusted correctly, your car will veer to one side. To adjust the trim, you’ll need to find the screws on the front or rear of the car that hold the wheels in place. Once you’ve found them, loosen them and adjust the wheels until the car is driving straight.

By following these simple steps, you should be able to fix most rc car steering problems. However, if your car is still having trouble, it’s time to take it to a professional. They’ll be able to diagnose the problem and get your car steering like new again.

You May Also Read: How to Fix Joystick on Xbox 360 Controller

Frequently Asked Questions

Do You Adjust the Steering on a RC Car?

different RC cars handle differently and require a different level of steering adjustment. However, generally speaking, you will need to adjust the steering on an Rc car as needed in order for it to steer accurately. This can be done by loosening or tightening the wheel bearings as necessary.

Why is My Rc Car Servo Not Working?

There are a few potential reasons why your rc car servo might not be working. Some of the most common issues include power loss, dried-up batteries, faulty wiring, and clogged filters. When you suspect that one of these factors is causing the problem, take appropriate steps to address it.

If power loss is the culprit, try moving your USB charger closer to the car servo or switching out batteries for a fresh set. If battery problems are suspected, replace them as soon as possible with brand-new ones. Failing that? Try unplugging and replugging your USB cable into both the receiver and car servo several times in quick succession.

Wiring can also become corroded if it’s exposed to moisture or other corrosive substances over time. In this case, repairs may require rewiring parts of your kit or replacing entire assemblies altogether.

Finally, check for any debris build-up in your filter system by gently tapping on it with a small screwdriver dipped in water; if there’s no response then you’ll need to clean it thoroughly using an appropriately sized filter cleaner such as Canofyte RC Servomasterâ„¢ Professional Cleaner (RcCarServos).

What Makes an Rc Car Turn?

the mechanism that makes an rc car turn depends on the specific car and its design. However, in general, rc cars use a variety of systems to power their motors and move their wheels. These systems include electric motors, internal combustion engines, and even hydraulic systems.

Ultimately, the system that is used to make an rc car turn will depend on the car’s design and purpose. For example, a car that is designed for racing might use a powerful electric motor to power its wheels. On the other hand, a recreational vehicle might use an engine to power its wheels.

What Does 2.4 Ghz Mean for Rc Cars?

A 2.4 GHz frequency is the most common in use for wireless network equipment, including routers and modems. This frequency range allows devices to connect wirelessly without interference from other electronic devices in close proximity.


When it comes to RC cars, many things can go wrong. One common issue is with the steering. If your RC car isn’t turning as smoothly as it used to, or if it seems like one side is dragging more than the other, you may need to fix the steering. We’ve gone through the steps to show you how to do just that in this article.

Rc Car Isn't Turning as Smoothly

Now that you know how to fix a rc car steering, it’s time to get out there and start driving! Be sure to practice in an open area to get the hang of the controls and how the car handles. Have fun and be safe while enjoying this hobby!

Leave a Comment