How to Fix a Noisy Fidget Spinner

Do you have a noisy fidget spinner? In this blog post, we’ll provide some tips on how to fix a noisy fidget spinner. If your fidget spinner is making too much noise, we’ll show you how to troubleshoot the problem and get it spinning quietly again. First, try checking the blade. If it’s bent or warped, you’ll need to straighten it out.

You can use needle-nose pliers for this. Next, make sure the bearing is properly lubricated. If it’s not, apply some oil or grease to it using a Q-tip. Finally, check the screws that hold the blade in place. Make sure they’re tight; tighten them up using a Phillips head screwdriver if they’re loose. Your fidget spinner should now be nice and quiet! Read on to know more!

How to Fix a Noisy Fidget Spinner

Summary: Fixing a noisy fidget spinner can be easy! First, remove all of the screws from the backside of the spinner. Next, carefully remove the bearing from the center and lightly clean it using a small brush and some rubbing alcohol.

Re-assemble the spinner paying special attention to make sure all of the screws are tight. Finally, lube up the bearing with some light oil or graphite lube and re-mount it in its casing. Your fidget spinner should be spinning smoothly once again!

Why Does Spinner Make Noise?

The spinner doesn’t always spin silently, and it might rotate only a couple of times with sound. Several different reasons can cause the noise. Sometimes the problem is in bearings; they are not well-aligned or have some dirt/dust inside. Also you can find fidget spinner that has thicker & shorter bearings, so their friction makes noise.

Another reason can be that the spinner is not balanced well because of two or more strong neodymium magnets inside/around the center. The greater number of magnets, the higher speed you can achieve. But if there are too many magnets inside/outside, the spinner will rotate less time without noise. Also, it creates a huge centrifugal force, which creates a strong vibration.

10 Ways on How to Fix a Noisy Fidget Spinner

1. Bearing Carbon Block Spinner

This is a way to build a fidget spinner using a bearing carbon block and craft carbon fiber rods. The cage should have 2 or 3 holes that are not used for this spinner.

2. Bearing Oil Spinner

Another way you can fix that noise is by adding oil into your bearing. Again, there are different ways to go about this:

Add Oil Into Your Bearing
  1. Add a few drops of both silicone and mineral oil into the bearing. You can use a syringe for this! ( The impeller should facilitate the process by making it easier.)
  2. Using grease, put some on your spinner cap, and drop your bearings in. Let it sit for a day.
  3. Using silicone grease, put some on your bearings and let it dry overnight.

3. Spinner O-Ring Spacer

O-ring spacers are small rings that fit into the center of your bearing caps. This way you can tighten or loosen the spinner without actually modifying it. I’m trying to make it work with a smaller, more elegant type of spinner. The problem is that the inner mechanism keeps sticking out. I’m going to have to talk to Eric about that one.

There’s also a set of O-rings for the intake tube, so you can tighten it without actually permanently modifying the tube itself.

I really like that it gives the spinner a nice tight fit without requiring any modification to the spinner.

4. Spinner Cap Glue

If you want to fix your spinner without oiling the bearings, you can try gluing it. Get a glue that can bond plastic together, like superglue. Test the glue by putting a small amount on the center of your spinner cap. If the glue dries and sticks to the plastic, then it should work.

5. Spinner Plate Nuts

Spinner plate nuts are a type of bearing cap that can be used with a fidget spinner. They help to tighten the spacers and keep the spinner in the center.

6. Spinner Ring

If you have lost or broken your spinner ring, you can use this method to fix that problem! If you cannot find a spinner ring anywhere, then there is another way to do it. First, drill out the center of your bearing cap and make two holes on each bearing side. Next, take a long screw through each hole. This should tighten the spinner without having to find another ring!

Broken Spinner Ring, Make Noise

7. Bearing Spacers

If your bearings are pressed too far, you can use this method to fix that problem. First, using the instructions above, take out the center of your bearing caps, and using super glue, put a ring of it on the middle of your bearings. After drying, use an x-acto knife and push the spacers down to where you want them.

8. Add weight

If you have a spinner that you don’t want to stress out, you can put small washers into the center of the bearing cap. This will add extra weight to the spinner and make it more balanced.

9. Adjust Your Strings Tension

This one requires a fidget spinner that allows for adjustments on the strings. Using pliers, tighten the strings around the spinner. This should put less stress on your bearings and lower its noise!

10. Replace Spinner Axle

If you have tried everything and your bearings still make too much noise, then replacing your axle is the only way to fix that. First, using a drill press or hand drill, unscrew your spinner cap and get rid of it. Next, take out the hub which holds the string in place with the bearings. Replace this with a new one that is sold for this purpose.

If your bearings are too tight, then using a screwdriver, you should be able to pry it out a little bit and make the spinner spin smoother. This also decreases noise. Use caution when doing this, as you can damage your bearing!

Replacing Your Axle Is the Only Way to Fix That

Some Helpful Tips to Prevent Fidget Spinner from Making Noise

1. Some bearings will stay quiet until they develop a little speed. If your bearing is already spinning smoothly and quietly, try slowing it down with your fingers.

2. Another quick trick to dampen the sound of spinner noise is to put a piece of tape(sticky side up) over one-half of the bearing. You can do this with your fingers or use tweezers.

3. If your spinner uses a ball bearing, you could try removing the shield/race that keeps the balls in place inside the bearing. This should significantly reduce noise and reduce spin time, so keep that in mind before making irreversible changes to your bearing.

4. If you have a spinner with a hybrid bearing(consisting of both an inner metal shield and an outer cage), this guide will show you how to remove the outer cage to reduce noise.

5. If your bearing is noisy but still runs smoothly, try applying a few drops of sewing machine oil or any lightweight oil (e.g., 3-in-1, WD-40). This will usually quiet it down and increase spin time simultaneously!

6. If you have an out-of-round inner shield, it might be causing excess noise. You can try testing that theory by removing the shield entirely and see if that fixes the problem. If that works, you might be able to reshape your shield with a round tool gently.

Factors to Consider Before Buying A Fidget Spinner

1. Spin Time

The spin time of a fidget spinner is usually the first factor buyers consider. A good fidget spinner has a spin time of at least 2 minutes.

2. Noise Level

Noisy fidget spinners are a major turn-off for most people because the noise can get very annoying. You want to look for a quiet fidget spinner.

3. Weight

Buyers should also consider the product’s weight before buying it. The heavier a fidget spinner is, the more powerful and smooth it will turn in your hands. Therefore, it’s important to buy a product that has just enough weight and not too much or too little.

4. Material

The material of the fidget spinner should not be too hard to prevent your hands from getting sore after continuous spinning or too soft for maximum performance, either. You want a product that fits just right in your hand to have long hours of fun without straining your hands.

The Fidget Spinner Should Not Be Too Hard

5. Quietness

A loud fidget spinner is not something many people want to buy. You want a product that you can play with without distracting those around you or attracting unnecessary attention.

How Long Will a Fidget Spinner Spin?

The average fidget spinner has a spinning time of 2-3 minutes. This is enough for most people, but if you want to make your spinner spin even longer, some tricks can help you achieve this. For example, you could try applying oil to the ends of the central bearing (this will increase its smoothness). A bearing is a metal ball that allows the spinner to spin smoothly. It can be removed easily with a screwdriver.

One of the most popular tricks is tightening the center bearing on a fidget spinner with screwdrivers if it wobbles or starts spinning unusually slowly. You can buy special tools for this from Amazon or eBay, but it can do the trick if you have a screwdriver lying around. You don’t need to be gentle when tightening the nut, as long as it doesn’t break.

You Can Check It To Fix an Infinity Cube

Frequently Asked Questions

Why is My Fidget Spinner So Loud?

Fidget spinners are notorious for being exceptionally loud, and there seem to be no bounds to the amount of noise they can produce. This may be due to their small size and the fact that they can move a lot of air at once. When you spin your fidget spinner, it creates a surprising amount of turbulence in the air. This turbulence is magnified when sound waves travel through this medium and cause them to vibrate more intensely.

This high degree of vibration often leads to excessive noise levels, which is why fidget spinners tend not only to generate audible clicking sounds but also whirring noises and booms. If you’re prone to headaches or other forms of ear pain, spinning your fidget spinner might not be the best idea!

Should You Oil a Fidget Spinner?

Some people believe that oiling a fidget spinner will help to keep it spinning for a longer period of time, while others believe that it’s unnecessary and could even damage the spinner.

Personally, I think that it’s up to each individual to decide whether or not they think oiling the spinner is necessary. There is no real scientific evidence to back up either side of the argument. If you are in a camp that believes that oiling the spinner will help to keep it spinning for a longer period of time, then you may want to do this. If you are in a camp that believes that oiling the spinner could damage it, then you may want to refrain from doing this. It’s ultimately up to you!

Can You Put Wd-40 in a Fidget Spinner?

as each spinner will be different and may require a different approach in order to fidget. Some individuals have found that putting WD-40 inside the spinner allows them to spin it longer and more freely while others claim that the lubricant breaks down over time and messes up their device. As with any other DIY project, proceed at your own risk

Do I Make My Fidget Spinner Quieter?

Some tips that may help include attaching a weighted or elastic band to the spinner to make it quieter, or using a smaller fidget spinner that is less likely to make noise. Alternatively, you can try putting the spinner in your pocket or holder.

Can I Increase My Fidget Spinner Speed?

Yes, you can! Many fidget spinners come with different speeds, so it is important to find the speed that works best for you. Some people prefer a lower speed while others like to play at a higher level. There are also apps available that allow users customize their spinner’s speed.

By adjusting your speed, you can help increase your focus and reduce anxiety or boredom. You can also use this tool as an aerobic activity by gradually increasing the pace over time.


Fidget spinners are popular toys designed to help people focus and calm down. However, many people find that these toys are too noisy and disruptive. In this blog post, we have discussed a few tips on how to fix a noisy fidget spinner.

If your fidget spinner is making too much noise, try using some of our tips in this blog post. By following these simple steps, you should be able to reduce the amount of noise your toy makes. Have you tried any of these methods? Let us know in the comments below!

You Can Check It Out To Fix Ripped Fishnet Tights

Leave a Comment