Do you know what to do if your furnace lockout? It’s a situation that no one wants to find themselves in, but if it happens, there are some things that you can do to get yourself back up and running. This is a common problem with furnaces and is usually easily fixed.
Sometimes, all it takes is a simple reset, while other times, you may need to call in a professional. However, before you do anything, it’s important to understand what a furnace lockout is and how it can be fixed. In this blog post, we’ll give you a few steps on how to fix furnace lockout so that you can stay warm all winter long. Keep reading for more information!
Summary: If your furnace is exhibiting a lockout, the first step is to locate the reset button. This will usually be located on the control board of the furnace. The reset button can be switched off and then on again to restore power.
If that does not work, it may be necessary to check for any wiring or gas connection issues and disconnect them if present. If all else fails, it may be necessary to call an HVAC technician for assistance.
What Causes a Furnace Lockout?
There are a few different reasons that your furnace may go into lockout mode. The most common reason is that the furnace has exceeded its maximum temperature limit. This safety feature is in place to prevent the furnace from overheating and causing a fire.
Another common reason for a furnace lockout is a faulty or damaged pressure switch. The pressure switch is responsible for monitoring the pressure of the gases inside the furnace. If the pressure gets too high, the switch will trip and cause the furnace to go into lockout mode.
Lastly, a dirty or clogged filter can also cause a furnace lockout. The filter prevents debris and dust from entering the furnace. If the filter becomes clogged, it can restrict the airflow to the furnace and cause it to overheat.
7 Steps on How to Fix Furnace Lockout
Step 1: Verify the Power Switch
The first thing you’ll want to do is check that the power switch is turned on. This is usually located near your furnace and may be labeled as a breaker, fuse, or switch. Carefully check the switch to see if it’s in the “on” position.
Step 2: Inspect the Furnace Filter
If the power switch is on and your furnace still isn’t working, the next step is to check the furnace filter. A clogged filter can cause a furnace to shut down. Inspect the filter and replace it if necessary. You also need to make sure that the filter is installed correctly.
Step 3: Check the Thermostat Settings
If the power switch and furnace filter are in good working order, the next step is to check the thermostat settings. Make sure that the thermostat is set to “heat” mode and not “cool” or “off.” Also, check the temperature setting to ensure it’s set at a comfortable level.
Step 4: Inspect the Blower Motor
If the thermostat settings are correct, the next step is to inspect the blower motor. This is located in the furnace and may be covered by a panel. You need to check the voltage to the motor and make sure that it is receiving power. If it is not, you will need to replace the motor.
If the motor is getting power but is still not working, you may need to oil the bearings. This can be done with a few drops of lubricating oil, such as WD-40. Just a few drops are all that is needed.
If the motor does not start, it may need to be replaced.
Step 5: Inspect the Burners
The next step is to inspect the burners. First, make sure that the gas valve is turned on. Then, check for any blockages in the burner ports. If you see any blockages, use a wire brush to clean them out. Finally, check the igniter to make sure that it is working properly.
If your furnace still doesn’t turn on after following these steps, it may be time to call a professional for help.
Step 6: Check the Pilot LightIf
your furnace has a pilot light. The next step is to check it. First, make sure that the gas valve is turned on. Then, locate the pilot light assembly and inspect it. If the pilot light is out, you will need to relight it. To do this, first, locate the reset button. It is usually located near the pilot light assembly. Once you have found the reset button, press and hold it for 30 seconds. Then, use a lighter to relight the pilot light. If the pilot light does not stay lit, there may be a problem with the gas supply. If this is the case, you should contact a qualified technician.
Step 7: Inspect the Electrical Connection
If the furnace still isn’t working, the next step is to inspect the electrical connections. First, check all of the wires to make sure that they are tight and not loose. Next, check the circuit breaker or fuse box to see if there has been a blown a fuse or tripped circuit breaker. If so, reset the breaker or replace the fuse. Finally, check the thermostat to see if it is set correctly.
If the furnace still does not work, it is time to call a professional. A professional can diagnose the issue and make the necessary repairs.
If you have followed all these steps and the furnace isn’t working, then it is time to call a professional. A professional can diagnose and fix the problem quickly and efficiently.
How Many Times Can I Hit the Reset Button on My Furnace?
If you have to hit the reset button on your furnace more than once in a heating season, there could be a bigger problem. Try these tips to see if you can get to the bottom of it.
First, check your air filter and replace it if it’s dirty. A clogged air filter is one of the most common reasons furnaces must be reset.
If that doesn’t do the trick, look at your ductwork. If there are any leaks or holes, seal them up with duct tape or fiberglass insulation.
Next, check for debris around the furnace. Make sure nothing is blocking the intake or exhaust vents.
If you’ve tried all these things and your furnace is still shutting off, it’s time to call a professional. There could be a problem with the furnace itself, and it’s always best to err on the side of caution when it comes to your home’s heating system.
What is a Soft Lockout on a Furnace?
When your furnace is in soft lockout mode, the furnace has tried to turn on too many times without successfully igniting the gas. This is a safety feature that is built into furnaces to prevent them from overworking and potentially causing a fire.
If your furnace is in soft lockout mode, the first thing you should do is check the power supply. Make sure that the furnace is plugged in and that the circuit breaker has not been tripped. If everything looks fine on the power front, then the next thing to do is check for any blockages in the exhaust pipe. A blockage in the exhaust pipe can cause the furnace to overheat and go into soft lockout mode.
Where is the Reset Button on My Furnace?
If your furnace has a reset button, it will usually be located near the bottom of the unit. There will be a small red or black button that you can press to reset the furnace. If you cannot find the reset button, consult your furnace’s owner’s manual. To reset the furnace, simply push the button and wait for the unit to restart. If your furnace does not have a reset button, you may need to contact a professional for assistance.
Safety Tips to Fix Furnace Lockout
If your furnace has been locked out, there are a few things you can do to try and reset it. However, before you start working on your furnace, you must understand the dangers involved. Furnace lockout is a serious safety issue that should not be taken lightly.
- First, make sure that the power to your furnace is turned off. If you’re unsure how to do this, contact your local utility company.
- Once the power is off, look at the lockout switch. This is usually located near the control panel of your furnace. In some cases, it may be found on the side of the unit.
- If the switch is in the “on” position, flip it to the “off” position.
- Once the switch is in the “off” position, wait a few minutes and turn the power back on to your furnace.
- If your furnace still doesn’t come on, reset the thermostat to the correct temperature.
- If the furnace still doesn’t come on, check the circuit breaker or fuse box. If a fuse has blown, replace it with a new one. If the circuit breaker has tripped, flip it back to the “on” position.
- If the furnace still doesn’t come on, there may be a problem with the gas line. Check to ensure the gas valve is in the “on” position.
If the furnace still doesn’t come on, contact a professional for assistance.
You Can Check It Out To Fix Ignition Lockout on Furnace
Conclusion
Furnace lockout can be caused by various reasons, most commonly due to a problem with the furnace thermostat or limit switch. To fix a furnace lockout, it is important to determine the root cause of the problem.
If you are comfortable doing so after reading this article on how to fix furnace lockout, you can try troubleshooting the furnace on your own. If not, call in a professional technician. Fixing a furnace lockout is usually a simple process, but it is important to take safety precautions when working with heating equipment.
You Can Check It Out To Fix a Rattling Furnace